DIY Copper Hose Stand

Trendy Tuesday

This past Sunday, we shared with y’all how we snazzed up our office entrance by creating a simple little rock border and a tonal landscape of ground covers.  Today, we wanted to show you how we dealt with that unsightly hose.  The obvious solution was to grab a brand spankin’ new hose from the local hardware store, but how do we keep the new hose from following down the same path of entanglement and muck?  We knew that one of those plastic wheels would help us make things tidy, but we SO did not want that eye sore to compound the injury that our air conditioner was already creating.  Nope.  We wanted somethin’ purdy!  Since we have been playing around with so many pipe and copper projects, we felt like it was the natural choice for materials.  Besides, copper has THE BEST patina when exposed to the elements.  Watching it transform slowly over the years from an orangey metal to a bright teal is absolutely amazing!

zest HQ outside redo_0000




2 pieces of 6′ M copper piping (M is easier to cut) (1″ width)

3′ length of rebar 

pipe cutter


3 T-connectors (1″ width)

2 elbow connectors (1″ width)

4 45-degree connectors (1″ width)

4 end caps (1″ width)

adhesive for metal
zest HQ outside redo_0002

Cut List:

2 pieces of pipe 5″ long

2 pieces of pipe 7″ long

2 pieces of pipe 10″ long

4 pieces of pipe 3″ long

upright stand can be cut to however tall you want your hose storage to stand

zest HQ outside redo_0009I truly call this whole process “Legos for adults!”  Start by making your cuts using the crazy easy-to-use pipe cutter.  Basically, measure and then clamp and twist until the cut goes through.
zest HQ outside redo_0010

Now, begin your “Lego” building with a T-connector and your two 5″ pieces of pipe.  Using your adhesive, create a ring of glue on the inside of your T-connector.

zest HQ outside redo_0011

Using a hammer to make things snug, connect the two pieces of 5″ pipe to opposite sides of the T-connector.

zest HQ outside redo_0012Now repeat the adhesive step with the other two T-connectors, attaching them to either end of your 5″ pieces.
zest HQ outside redo_0013

Now it is time to use the four 3″ pieces that your have cut.  Using the adhesive, insert them into either end of the T-connectors at both ends.

zest HQ outside redo_0014

Are you still with me??  I am telling you…think Legos. 😉

Now, grab your two 45 degree elbows and your two 90-degree elbows and attach them to your four 3″ pipe pieces.  You will have one side with two 90-degree elbows and one side with two 45-degree elbows.

zest HQ outside redo_0015

On the 90-degree elbow side, connect your two 7″ pipe pieces.  On your 45-degree elbow side, connect your two 10″ pipe pieces.  Finish the 10″ pieces with an end-cap, and the 7″ pipes with another 45-degree elbow and then an end-cap.  You will have built a shape like this:

zest HQ outside redo_0016

The last assembly step before heading outside is to attach the long upright piece that connects to the very first T-connector at the base of this little creation.  Again, this piece can be cut however long you desire, only dependent on how tall you want your hose storage to stand.  I opted for about 4′, which allowed for part of it to be buried below the surface a bit when installed.  Time to head outside and prepare my site!

zest HQ outside redo_0003

Begin by digging a hole in the location you desire for your hose storage.  I went down about a 1 1/2′.  Then, grab your bag of Quikrete and filler up!

zest HQ outside redo_0004

Since Quikrete only needs water to set, I watered the mix and gave it a good stir.

zest HQ outside redo_0005zest HQ outside redo_0006

Now, grab your piece of rebar and jab it down into your mixed Quikrete.  I wound up grabbing my hammer to give it a few good wacks, just to get it nice and secure.

zest HQ outside redo_0007

With the rebar set in about 12″ into the Quikrete, it is time to grab the copper stand.

zest HQ outside redo_0008

Simply slide the copper base over the rebar and push it deep down into the Quikrete.  The very last step is to let the Quikrete “set” overnight.  You want things cured and solid before covering the Quikrete with garden soil.
zest HQ outside redo_0017

zest hq front garden_0000copper hose holder_0000

Not too shabby, if ya ask me!  Goodness, I cannot wait until I start to see some flecks of teal on the weather-exposed copper.  This is going to be so pretty!!  So pretty, and so darn easy!







Leave a Reply

Your email address will not be published. Required fields are marked *